Tag Archives: Inverse ARP

ARP, InARP, RARP, Proxy ARP & Gratuitous ARP?? Whats this all about!!

There are lots of Arp terms in Network field today i.e. ARP, RARP, InARP, Proxy ARP and Gratuitous ARP. This was really confusing for me atleast in my early networking days and I am sure people who are new to networking must be in same situation. So I thought of putting the details here in order to alleviate their confusion. So let’s start

 1) ARP (Address Resolution Protocol)

ARP or Address Resolution protocol is a protocol as its name states which works on TCP/IP Layer 2. Networking between devices can’t be done without using this protocol which basically helps in getting the mac-address of connected router or gateway from IP Address. So for example, host/computer is connected to Router over Ethernet and we have manually configured IP Addresses on both sides with Router acting as Gateway for Host computer. Before Host can send packet to Router, it needs to build Layer 2 Frame and this frame encapsulates Packet including Payload/Date. You know that Frame has Source MAC-Address and Destination MAC-Address fields apart from other fields. So host can take out source-mac address from value burned in its NIC (Network Interface card) however it won’t be knowing the destination mac-address and in order to get the value of destination mac address host uses ARP. So Host will send broadcast ARP request message (destination FF:FF:FF:FF:FF:FF MAC address), which is accepted by all computers, requesting an answer for router’s gateway mac-address which is returned by Router in form for Arp-reply as a unicast.

APR_Packet Format

54:1e:56:f7:7d:4a > ff:ff:ff:ff:ff:ff, ethertype 802.1Q (0x8100), length 46: vlan 602, p 0, ethertype ARP, arp who-has 20.20.20.20 tell 20.20.20.200

00:00:00:5e:00:00 > 54:1e:56:f7:7d:4a, ethertype 802.1Q (0x8100), length 64: vlan 602, p 0, ethertype ARP, arp reply 20.20.20.20 is-at 00:00:00:5e:00:00

2) InARP ( Inverse ARP)

Now what is Inverse Arp then? Inverse ARP as you might guess is the opposite of ARP.  Instead of using layer 3 IP address to find a layer 2 MAC address, Inverse ARP uses layer 2 MAC addresses to find a layer 3 IP address.

Inverse ARP was mostly used by Framerelay and ATM Networks to map the DLCI to IP Address. So router basically asks the IP Address of destination or other end of PVC by listing DLCI for that router.

3) RARP (Reverse ARP)

Reverse ARP is same as Inverse ARP however it was mainly used for device configuration. In InARP IP Address of remote end was being asked however RARP task is to get the IP Address for its own purpose.

A network administrator creates a table in a local area network’s gateway router that maps the physical machine (or Media Access Control – MAC address) addresses to corresponding IP Addresses. When a new machine is set up, its RARP client program requests it’s IP Address from the gateway router. Assuming that an entry has been set up in the router table, the RARP server will return the IP address to the machine which can store it for future use.

Reverse ARP has been deprecated and replaced by BOOTP which was then later replaced by DHCP.

4) Proxy ARP

As we mentioned above that the ARP is basically to find out Layer 2 address from Layer 3 IP Address. Now suppose host is connected to router over Ethernet and host has one address 10.10.0.1/16 and router has 10.10.10.0/24.

Host wants to resolve the ARP for 10.10.0.100 and thinks that Router is also in same subnet so should be able to get the mac-address however as Routers by design limit broadcast domains so won’t be sending the arp reply back and request will be rejected. If on the other hand router has any other interface connected to 10.10.0.0/16 network and proxy-arp is enabled, in that case Router will send the arp reply to host by listing its own mac-address basically acting as proxy for destination Network. In this case we don’t have to change the netmask of host and it will work fine.

On Cisco interfaces, when we configure “no ip proxy-arp”, we are disabling this behaviour.

5) Gratuitous ARP

Gratuitous ARP is by far the interesting version of ARP and lets see how gratuitous ARP works. We will go through 2 use cases here:

Firstly let’s discuss some of the properties of GARP

  • Both source and destination IP in the packet are the IP of the host issuing the gratuitous ARP
  • The destination MAC address is the broadcast MAC address (ff:ff:ff:ff:ff:ff) . This means the packet will be flooded to all ports on a switch
  • No reply is expected

1st use case of GARP is finding duplicate IP Address on LAN. Host which wakes up lets say after reboot sends GARP by putting the Sender IP address and Target IP Address as its own IP and broadcast the frame using Ethernet II destination address of all FFs.

It is not expecting any reply however if someone replies back with mac-address corresponding to Target IP Address then it means that IP address is being used somewhere else in LAN which is a problem. In this way host can detect duplicates.

2nd use case of GARP is case of redundancy protocols like VRRP/HSRP. VRRP (Virtual Redundancy Routing Protocol) or HSRP works by providing redundant physical gateways to host reachable over same Virtual address in order for Host to reach destination networks even though one physical router is down.

GARP_VRRP

VRRP has VIP (Virtual IP) concept which is shared among 2 VRRP routers and one of them is Active at any one time and holds Virtual MAC-Address corresponding to this VIP. Whenever host requests for ARP for 10.1.1.1, Master router will reply back with Virtual MAC Address.

Now we know that Switch updates its MAC Address table by looking at Mac address being learned on which port. Assuming Router 1 is Master currently, Switch will have entry in its table for Virtual Mac address learnt via Eth1 interface.

Let’s suppose that Router 1 goes down and in that case Router 2 sends GARP forcing switch to update its MAC-address table in order for it to update new location of Virtual MAC address reachable over new port i.e Eth2.

In this way, Host never sees an issue and packets sent by it will always egress a correct port.

Format of Gratuitous ARP

GARP Format

So that’s all, I hope you enjoyed this blog and I was able to clear some of your confusion. Let me know if you still have any doubt.

Thanks

Mohit Mittal

Advertisements